Yamaha r 1330

Page 1

MICRO COMPONENT SYSTEM MCS-1330
RECEIVER/SPEAKERS

R'1330/NS-BP4OO

SER E MANU

The MCSr1330 consists of the R4330, CDr1330 and NSrBP400.
This sen/ice manual ls for the R71330/NSrBP4OO.
For servlce manual of the CD71330, please refer to the following publication number:

0071330:

MCSrl33O lie R7133oc CD71330 35H) NSsBP4OO Tlfirflzehfvifio
Z aw- E747: 1 7) LI: Rel 330/NSrBP400 Ala-63s
cm 330 lfiIth- 517: 1 7) PITTEEEEET y/ {-73%}? L? < fiifmo

CD-1330:

IMPORTANT NOTICE

This manual has been provided for (he use of authorized YAMAHA Retmlers and their service personnel,

It has been assumed that basic service procedures inherent to the industry. and more specifically YAMAHA Products. are already known
and understood by the users. and have thetetore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury.
destruction of expensive components. and failure of the product to pertorrn as specified. For these reasons, we advise
all YAMAHA product owners that any service I'equll'ed should be performed by an authorized YAMAHA Retailer oi-
the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization. certification or
recognitlon of any applicable technical capabilities. or establish a pi-incipleeagent relationship of any form
The data provided is believed to be accurate and applicable to the unitis) indicated on the cover. The research engineering and service
departments Of YAMAHA are continually striving to improve YAMAHA products, Modifications are. Iherefore, inevitable and
specifications are subyect to change without notice or Obligation to retrofit Should any discrepancy appear to exist. please cotitact the
distributors Service Division,

WARNING: static discharges can destroy expensive components Discharge any static electricity your body may have 3;
accumulated by grounding yOuI'SEIfIO the ground buss In the unit (heavy gauge black wtres Connect to this buss). _'a
IMPORTANT: Turn the unit OFF during dtcassembly and part replacement, Recheck all work before you apply power to the unit. g
2
E
I CONTENTS §
To SERVICE PERSONNEL ........................................ 2-4 UPDATING FIRMWARE/ 8
PREVENTION OF ELECTROSTATIC DISCHARGE ...... 5 7 7 -Ls'7 I ngiilai ..................................... 16-20
SYSTEM COMPOSITION / azimfififi DISPLAY DATA
FRONT PANELS Ic DATA ........... 22-27
REAR PANELS .. PIN CONNECTION DIAGRAMS . 28-29
REMOTE CONTROL PANELS BLOCK DIAGRAM ................
SPECIFICATIONS / gem; ..... PRINTED CIRCUIT BOARDS ..
INTERNAL VIEW ........................................ SCHEMATIC DIAGRAMS ........
DISASSEMBLY PROCEDURES / fining 11-13 REPLACEMENT PARTS LIST .
TEST MODE / ix l~{- F ....................... 14-15 REMOTE CONTROL

' :wv- tx7217llzl1e137-7égfimfiiiflfiilfilfi bruzn
Triis Service Manual uses recycled paper.

Copyright © 2005 YAMAHA CORPORATION All rights reserved.
Thls manual is copyrighted by YAMAHA and may not be copied Or
redistributed either In print or electronically Without permission,

YAMAHA

YAMAHA CORPORATION

P.O.Box 1, Hamamatsu, Japan
animate 08.12

Page 2

o
o
v
n.
P
U)
E
o
n
n
T
I:

R-1330/NS-BP400

I TO SERVICE PERSONNEL

.Critical Components Information

Components having special characteristics are marked A and
must be replaced with parts having specifications equal to those
originally installed.

2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.

0 Meter impedance should be equivalent to 1500 ohms shunted
by 0.15 uF.

For U model
IE9 CAUTION

AC LEAKAGE
WALL EQUIPMENT TESTER OR
OUTLET UNDER TEST EQUIVALENT

@ID-

J:

INSULATING
TABLE

- Leakage current must not exceed 0.5mA.
0 Be sure to test for leakage with the AC plug in both polariA
ties.

*Ai" F1: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 5A, 125V

FUSE.

For C model
CAUTION

F1: REPLACE WITH SAME TYPE 5A, 125V FUSE.

ATTENTION

F1: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 5A, 125V.

WARNING: CHEMICAL CONTENT NOTICE!

This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive

harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON

WHATSOEVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or

expose eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before

handling food.

About lead free solder l fiflal \DfiIZ'DLT

All of the P.C.B.s installed in this unit and solder joints are
soldered using the lead free solder.

Among some types of lead free solder currently available,
it is recommended to use one of the following types for
the repair work.

0 Sn + Ag + Cu (tin + silver + copper)

0 Sn + Cu (tin + copper)

0 Sn + Zn + Bi (tin + Zinc + bismuth)

Caution:
As the melting point temperature of the lead free solder
is about 30°C to 40°C (50°F to 70°F) higher than that of
the lead solder, be sure to use a soldering iron suitable
to each solder.

$t§§ll%§i$hfb\é?NT®§l&£$Ul \/ filfllfl:
Otéteéafilifififia/ \y/JTV \ysflnlfirhfmim
fifil/ \yéiltlztln < amfifiofi U $335 léflifirfil:
liTEEUJot 5 tee/ax \) fiiUJIEfiHEIEIEé LEE

- Sn+Ag+Cu (fl + E + 31%)

- Sn+Cu (fi +313)
- Sn+Zn+Bi ($5 + fififi + EX?X)

52$ 2

Alia/Ell \y gimfitfi-EE Eliiéfimaik U l \y silzlEt/x 30 ~
40°CEI§FE§ < 7:: a mafia)? %n%h®/ \yiliéj
t/ wfibfélfififi < fifirv