Page 1
MAXI
FUSE 50 AMP
REMOTE GROUND
12 V
GREEN LED
NOISE GATE
YELLOW LED
LOW IMPEDANCE
ORANGE LED
THERMAL PROTECT
RED LED
POWER ON
SPEAKER OUTPUTS
LEFT RIGHT
LEFT RIGHTINPUTS
LEFT RIGHTOUTPUTS
Ð20Ð100 +10 +20
+
+POSITIVE
+
Ð
ÐNEGATIVE
Ð
BALANCED LINE
FAN
CROSSOVERMODE JUMPERS
:
CROSSOVER SIP SOCKETS
2 HP 3 LP 1 BYP 1 BYP
RCA OUTPUT AMPLIFIER
2 HP 3 LP 4 BNP
REMOTESWITCHED
12
VOLTS
16
GAUGE OR LARGER
NOTE
: ADD
50
AMP FUSE
AT POSITIVE TERMINAL OF
THE BATTERY
.
NOISE GATE THRESHOLD ADJUST
:TURN CLOCKWISE TO INCREASE SENSITIVITY
(GATE WILL OPEN WITH LESS INPUT SIGNAL
)
NOISE GATE SWITCH
:LEFT POSITION
= ON
; RIGHT POSITION
= OFF
GROUND
Ð 8
GAUGE OR LARGER
SPEAKER WIRE
Ð 14
GAUGE OR LARGER
POWER
Ð 8
GAUGE OR LARGER
BRIDGED OUTPUT CONNECTION ACCESSORY MODULE PORT
:REMOVE JUMPERS
(2)
PRIOR TO INSTALLATION OF ACCESSORY MODULE
.
JUMPERS MUST BE IN
-PLACE WHEN MODULE IS NOT INSTALLED
.
INPUT SENSITIVITY
:TO ADJUST INPUT GAIN
, MOVE JUMPER
(IF NEEDED
) Ð
AND INSTALL IT IN THE LOCATION WHICH
MATCHES YOUR INPUT SIGNAL LEVEL
. REFER TO THE ILLUSTRATION BELOW FOR PROPER JUMPER LOCATION
/ LEVEL SETTING
.
NOTE
: Ð20 dB = 10V Ð 17V
IS ONLY TO BE USED WITH BALANCED INPUT FROM A BALANCED SOURCE
.
Ð20 dB = 10V Ð 17V
Ð10 dB = 3V Ð 8V
0 dB = 1V Ð 3V
+10 dB = 300mVÐ1V
+20 dB = 100 Ð 300mV
CROSSOVERFREQUENCY SELECTION
:
TO CHANGE THE FREQUENCY
OF EITHER THE HIGH AND
/OR
LOW PASS FILTERS
, REMOVE
AND REPLACE THE FRE
-
QUENCY MODULE
(SIP
)
LOCATED ON THE CIRCUIT
BOARD NEXT TO THE
CROSSOVER MODE JUMPERS
.
NOTE THAT THE IDENTITY OF
THE HIGH
&
LOW PASS
SOCKETS ARE NOT MARKED
ON THE BOARD . REFER TO
THIS DRAWING FOR LOCA
-
TION
& THE CHART ON THE
BACK FOR THE AVAILABLE
SELECTION OF SIP
/ FRE
-
QUENCY VALUES
.
RCA OUTPUTS
:
3 Ð L
OW
PASS
2 Ð H
IGH
PASS
1 Ð BYP
ASS
AMPLIFIER
:
4 Ð B
AND
PASS
3 Ð L
OW
PASS
2 Ð H
IGH
PASS
1 Ð BYP
ASS
LOWPASSSIP
INDEPENDENT LEFT AND RIGHT AMPLIFIER GAIN
CONTROLS
Ð ROTATE CLOCKWISE TO INCREASE SENSITIVITY
.
XTANT TECHNOLOGIES 7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 PHONE: 888.449.8268 FAX 602.431.8600
HIGH PASS SIP
BONDED FIN
HEATSINK
INSTALLERÕS
REFERENCE
.............. XTANT 2200
IX
..............
Caution: SHARP EDGES
be careful when
handling top and
bottom metal.
Left
right
Balanced line: Disable (off) jumper position
Enable (on)
SERVICE
JUMPER
: REMOVING JUMPER WILL TURN
-OFF AMPLIFIER WHEN
REMOTE TURN
-ON, GROUND AND
12 V
OLT CABLES ARE CONNECTED TO
AMPLIFIER
. USE TO SERVICE
/ADJUST AMPLIFIER WHEN IN USE
.
