Sunfire theater grand owners manual

Page 1

2 User's Manual Safety Instructions 1. Read Instructions --“ All the safety and operation instructions should be read before the Sunfire Component is operated. 2. Retain Instructions - The safety and operating instructions should be kept for future reference. 3. Heed Warnings - All warnings on the Component and in these operating instructions should be followed. 4. Follow Instructions - All operating and other instruc- tions should be followed. 5. Water and Moisture - The Component should not be used near water - for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. 6. Ventilation - The Component should be situated so that its location or position does not interfere with its proper ventilation. For example, the Component should not be situated on a bed, sofa, rug, or similar surface that may block any ventilation openings; or placed in a built-in installation such as a bookcase or cabinet that may impede the flow of air through ventilation openings. 7. Heat - The Component should be situated away from heat sources such as radiators, or other devices which produce heat. 8. Power Sources - The Component should be connected to a power supply only of the type described in these opera- tion instructions or as marked on the Component. 9. Power Cord Protection - Power-supply cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep- tacles, and the point where they exit the Component.10. Cleaning - The Component should be cleaned only as recommended in this manual. 11. Non-use Periods-The power cord of the Component should be unplugged from the outlet when unused for a long period of time. 12. Object and Liquid Entry - Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the Component. 13. Damage Requiring Service - The Component should be serviced only by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has spilled into the Component; or C. The Component has been exposed to rain; or D. The Component does not appear to operate normally or exhibits a marked change in performance; or E. The Component has been dropped, or its cabinet damaged. 14. Servicing - The user should not attempt to service the Component beyond those means described in this operating manual. All other servicing should be referred to qualified service personnel. Safety Instructions

Page 2

3 User's Manual 15. To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. Pour préevenir les chocs électriques ne pas utiliser cette fiche polariseé avec un prolongateur, un prise de courant ou une autre sortie de courant, sauf si les lames peuvent être insérées à fond sans laisser aucune pariie à découvert. 16. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means of the Component is not defeated.This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. ATTENTION - Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant las limites applicables aux appareils numériques de class A/de class B (selon le cas) prescrites dans le règlement sur le brouillage radioélectrique édicté par les ministere des communications du Canada. WARNING -“ TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRO- DUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND. EXAMPLE OF ANTENNA GROUNDING ACCORDING TO NATIONAL ELECTRICAL CODE INSTRUCTIONS CONTAINED IN ARTICLE 810-RADIO AND TELEVISION EQUIPMENT GROUND CLAMP GROUNDING CONDUCTORS (NEC SECTION 810-21) ANTENNA LEAD IN WIRE POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) SERVICE ENTRANCE EQUIPMENT GROUND CLAMPS GROUND CLAMPS ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) NEC NATIONAL ELECTRICAL CODE. NOTE TO CATV INSTALLER This reminder is to call the CATV system installer's attention to Article 820-40 of the NEC that provides guide- lines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. OUTSIDE ANTENNA GROUNDING If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the lead-in wire to an antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure above. Safety Instructions