Sony rdr gx 310 service manual

Page 1

- 2 - SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing -Keep the temperature of the soldering iron around 270˚C during repairing. -Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). -Be careful not to apply force on the conductor when soldering or unsoldering. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. WARNING!! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CAUTION: The use of optical instrument with this product will increase eye hazard. Unleaded solder Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. -Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! -Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. -Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

Page 2

- 3 - TABLE OF CONTENTS SERVICE NOTE 1. DISK REMOVAL PROCEDURE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION) ············ 5 1. GENERAL WARNING ················································································ 1-1 Precautions ················································································ 1-1 Ways to Use Your DVD Recorder ············································ 1-1 Quick Guide to Disc Types ························································ 1-2 Recordable and playable discs ··············································· 1-2 Playable discs ········································································ 1-2 Hookups and Settings ································································ 1-3 Hooking Up the Recorder ······················································ 1-3 Connecting a VCR or Similar Device ···································· 1-5 Connecting to a Satellite or Digital Tuner ···························· 1-6 Seven Basic Operations - Getting to Know Your DVD Recorder ·········································································· 1-6 Inserting and Formatting a DVD Disc (Disc Info) ················ 1-6 Recording a Programme ························································ 1-6 Playing the Recorded Programme (Title List) ······················· 1-7 Displaying the Playing Time and Play Information ·············· 1-7 Changing the Name of a Recorded Programme ···················· 1-8 Labelling and Protecting a Disc ············································· 1-8 Playing the Disc on Other DVD Equipment (Finalize) ········· 1-8 Timer Recording ········································································ 1-9 Before Recording ··································································· 1-9 Timer Recording (Standard/G-Code) ···································· 1-9 Checking/Changing/Cancelling Timer Settings (Timer List) ·········································································· 1-11 Recording From Connected Equipment ······························ 1-11 Playback ·················································································· 1-12 Playing ················································································· 1-12 Searching for a Title/Chapter/Track, etc ······························ 1-14 Playing MP3 Audio Tracks or JPEG Image Files ··············· 1-14 Erasing and Editing ································································ 1-15 Before Editing ····································································· 1-15 Erasing and Editing a Title ················································· 1-15 Creating and Editing a Playlist ············································ 1-16 Dubbing (HDD y DVD) ······················································ 1-17 Before Dubbing ·································································· 1-17 Dubbing ··············································································· 1-18 DV Dubbing (RDR-HX710/HX910 only) ······························ 1-18 Before DV Dubbing ····························································· 1-18 Recording an Entire DV Format Tape (One Touch Dubbing) ·············································································· 1-19 Program Edit ········································································ 1-19 Settings and Adjustments ························································ 1-20 Aerial Reception and Language Settings (Settings) ············ 1-20 Video Settings (Video) ························································ 1-21 Audio Settings (Audio) ························································ 1-21 Recording and Parental Control Settings (Features) ··········· 1-22 Disc and Remote Control Settings/Factory Settings (Options) ············································································· 1-22 Easy Setup (Resetting the Recorder) ··································· 1-23 Additional Information ···························································· 1-23 Troubleshooting ·································································· 1-23 Self-diagnosis Function (When letters/numbers appear in the display) ··············································································· 1-24 Notes About This Recorder ················································· 1-24 About i.LINK (RDR-HX710/HX910 only) ························· 1-25 Guide to Parts and Controls ················································· 1-25 Glossary ··············································································· 1-26 Language Code List ····························································· 1-27 Area Code ············································································ 1-27 2. DISASSEMBLY 2-1. UPPER CASE ································································· 2-2 2-2. TRAY COVER ASSEMBLY ·········································· 2-2 2-3. FRONT PANEL SECTION ············································· 2-3 2-4. SLIDE DOOR ································································· 2-3 2-5. FL-144 BOARD, FR-226 BOARD (RDR-GX310) FL-144 BOARD, FR-232 BOARD (RDR-HX710/HX910) ···················································· 2-4 2-6. EM-001 BOARD, EM BRACKET (RDR-GX310 (RU/SP)/HX710/HX910 (RU/SP)) ·········· 2-4 2-7. HDD SECTION (RDR-HX710/HX910) ························· 2-5 2-8. HDD (RDR-HX710/HX910) ·········································· 2-5 2-9. DVD SECTION ······························································· 2-6 2-10. DVD DRIVE ··································································· 2-6 2-11. RD-051 BOARD, RD BRACKET ·································· 2-7 2-12. D. C. FAN ········································································ 2-8 2-13. POWER SUPPLY BLOCK ············································· 2-8 2-14. AV-089 BOARD ······························································ 2-9 2-15. CIRCUIT BOARDS LOCATION ··································· 2-9 3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM ···································· 3-1 3-2. AV-089 BLOCK DIAGRAM ·········································· 3-3 3-3. RD-051 BLOCK DIAGRAM (1/2) ································· 3-5 3-4. RD-051 BLOCK DIAGRAM (2/2) ································· 3-7 3-5. POWER BLOCK DIAGRAM (1/2) ································ 3-9 3-6. POWER BLOCK DIAGRAM (2/2) ······························ 3-11 4. SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM ································ 4-1 4-2. SCHEMATIC DIAGRAMS ············································ 4-3 WAVEFORMS ································································ 4-3 - AV-089 (1/8) (POWER SUPPLY) SCHEMATIC DIAGRAM ······························ 4-5 - AV-089 (2/8) (AUDIO A/D CONV.) SCHEMATIC DIAGRAM ······························ 4-7 - AV-089 (3/8) (AUDIO OUT) SCHEMATIC DIAGRAM ······························ 4-9 - AV-089 (4/8) (TUNER) SCHEMATIC DIAGRAM ···························· 4-11 - AV-089 (5/8) (SYSTEM CONTROL) SCHEMATIC DIAGRAM ···························· 4-13 - AV-089 (6/8) (VIDEO INPUT SELECT) SCHEMATIC DIAGRAM ···························· 4-15 - AV-089 (7/8) (VIDEO AMP) SCHEMATIC DIAGRAM ···························· 4-17 - AV-089 (8/8) (CONNECTOR) SCHEMATIC DIAGRAM ···························· 4-19 - EM-001 (AUDIO PROCESSOR) SCHEMATIC DIAGRAM ···························· 4-21 - FL-144 (INDICATOR DRIVE) SCHEMATIC DIAGRAM ···························· 4-23 - FR-226 (LED DRIVE, FUNCTION KEY) SCHEMATIC DIAGRAM ···························· 4-25 - FR-232(LED DRIVE, FUNCTION KEY) SCHEMATIC DIAGRAM ···························· 4-27 - CN-243 (RELAY) SCHEMATIC DIAGRAM ···························· 4-29 - RD-051 (1/13) (SYSTEM CONTROL) SCHEMATIC DIAGRAM ···························· 4-31 - RD-051 (2/13) (256M SDRAM, 128M FLASH MEMORY) SCHEMATIC DIAGRAM ···························· 4-33 - RD-051 (3/13) (SW/UNSW BUFFER) SCHEMATIC DIAGRAM ···························· 4-35 - RD-051 (4/13) (128M NAND FLASH, 2-CH DAC, SRC) SCHEMATIC DIAGRAM ···························· 4-37