This is the 24 pages manual for sony icd p 320 service manual. Read or download the pdf for free.
If you want to contribute, please mail your pdfs to info@audioservicemanuals.com.
Page: 1 / 24
Extracted text from sony icd p 320 service manual (Ocr-read)
Page 1
2
ICD-P320
TABLE OF CONTENTS
1. GENERAL
...................................................................... 3
2. DISASSEMBLY
2-1. Case (Front) Assy ............................................................... 4
2-2. MAIN Board ....................................................................... 5
2-3. USB Board ........................................................................\
. 5
3. TEST MODE .................................................................. 6
4. DIAGRAMS
4-1. Block Diagram ................................................................... 9
4-2. Printed Wiring Board -“ MAIN Section -“ ........................ 11
4-3. Schematic Diagram -“ MAIN Section (1/2) -“ .................. 12
4-4. Schematic Diagram -“ MAIN Section (2/2) -“ .................. 13
4-5. Printed Wiring Board -“ USB Section -“ .......................... 14
4-6. Schematic Diagram -“ USB Section -“ .............................. 15
5. EXPLODED VIEWS
5-1. Case (Front) Section ......................................................... 19
5-2. Case (Rear) Section .......................................................... 20
6. ELECTRICAL PARTS LIST ................................... 21 Flexible Circuit Board Repairing
-K eep the temperature of the soldering iron around 270 °C
during repairing.
- Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
- Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement -N ever reuse a disconnected chip component.
- Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics. - Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
- Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
- Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder. Operating instructiondd
Page 2
3
ICD-P320
SECTION 1
GENERAL
This section is extracted
from instruction manual.
Index to Parts and Controls
Main unit
*There is a tactile dot beside the control to show the
direction to turn up the volume.
**The button has a tactile dot.
MIC (built-in microphone)
(microphone) jack
Display window
DISPLAY/MENU
DIVIDE
xSTOP
zX REC (record) /PAUSE
-“ . (review/fast backward) /
>+ (cue/fast forward) (SELECT)
SpeakerOPR (operation) indicator
ERASE
VOL (volume) control*
HOLD
Nx PLAY/STOP (ENTER)**
i (earphone) jack
Rear
Battery
compartment
Hook for handstrap
(not supplied) USB connector
Display window
Folder indicationRemaining battery
indicator
Microphone sensitivity
Alarm indicator
Selected message number
REC DATE (recorded date)
indication
REMAIN indicator
Remaining memory
indicatorRecording mode
indication
REC (recording)
indicator
Repeat play indicator
Number of messages in
a folder/Menu
indication/Counter /
Remaining time
indication /Recording
date indication /Current
time indication /
Messages EASY-S (Easy Search)
indicator