Sharp cd xp 120w service manual

Page 1

CD-XP120W

SHARP SERVICE MANUAL

No. S7254CDXP120W

MINI COMPONENT SYSTEM

MODEL CD-XP120W

CD-XP120W Mini Component System consisting of CD-XP1 20W
(main unit) and CP-XP120 (speaker system).

- In the interests of user-safety the set should be restored to its
original condition and only parts identical to those specilied be
used.

COM PACT -
[fl canny Séé

DIGITAL AUDIO

/- CONTENTS

SAFETY PRECAUTION FOR SERVICE MANUAL
VOLTAGE SELECTION .......
AC POWER SUPPLY CORD
SPECIFICATIONS .....
NAMES OF PARTS
DISASSEMBLY ..........
REMOVING AND REINSTALLING THE MAIN PARTS.
ADJUSTMENT
TEST MODE .......
NOTES ON SCHEMATIC DIAGRAM
TYPES OF TRANSISTOR
BLOCK DIAGRAM ............
SCHEMATIC DIAGRAM /W|R|NG SIDE OF P.W.BOARD.
VOLTAGE .........................
FUNCTION TABLE OF IC.
FL DISPLAY ......................
REPLACEMENT PARTS LlST/EXPLODED VIEW

-
This document has been published to be used

SHARP CORPORATION for after sales service only.

The contents are subject to change without notice.

Page 2

CD-XP120W
SAFETY PRECAUTION FOR SERVICE MANUAL

WARNINGS
THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1 BUT THE LASER
COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR CLASS 1. THEREFORE IT IS
IMPORTANT THATTHE FOLLOWING PRECAUTIONS ARE OBSERVED DURING SERVICING TO PROTECT YOUR EYES
AGAINST EXPOSURE TO THE LASER BEAM.
1-WHEN THE CABINET IS REMOVED, THE POWER IS TURNED ON WITHOUTA COMPACT DISC IN POSITION AND THE
PICKUP IS ON THE OUTER EDGE THE LASER WILL LIGHT FOR SEVERAL SECONDS TO DETECT A DISC. DO NOT
LOOK INTO THE PICKUP LENS.
2-THE LASER POWER OUTPUT OF THE PICKUP UNIT AND REPLACEMENT SERVICE PARTS ARE ALL FACTORY
PRESET BEFORE SHIPMENT.
DO NOT ATTEMPT TO READJUST THE LASER PICKUP UNIT DURING REPLACEMENT OR SERVICING.
3-UNDER NO CIRCUMSTANCES STARE INTO THE PICKUP LENS AT ANY TIME.
4-CAUTION-USE OF CONTROLS OR ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

Laser Diode Properties
Material: GaAlAs
Wavelength: 780 nm
Emission Duration: continuous
Laser Output: max. 0.6 mW

Eluflflll-IIWISIBLE uszn minim: wuzn DPEll.
nu nut suns mm mm at VIEW murmur WITN
amen lISYRIIMEllYR
WARIllltlirllllslnllYBlni utsrmmulun wm mat
ssnrruzr. mutt Ill lllE strinulmie :muru uDER
mam mt IlPIisCMEH HILFSMIHEUI BEWAEMEI .
ATIEIIIiIlIlrMVnH um lIlIlSllllE EH us It nIWEImlRE lllllIIIIyll
HE Ms nzmnzx LE msmv mmrmur nu ms at; , ililiiIIIliiIIleilII
Illillillllilfls amour: IIIIIIIIIIIIIIIIIIIII
llIIIiiiiII ill
I iiiiiiilIIIIIIIIIIiiIii

mi
iilII
ill
will

VOLTAGE SELECTION

Before operating the unit on mains. check the preset voltage. If the voltage is different from your local voltage, adjust the voltage
as follows.
Turn the selectorwith a screwdriver until the appropriate voltage number appears in the window (1 10 V. 127 V, 220 V or 230 V » 240 V AC).

AC POWER SUPPLY CORD
QACCEOOOZSJOO QACCAOOOZSJOO

rm .|

IIlllii

QACCLOOOZSJOO/QACCZOOOBSJOO