This is the 56 pages manual for Sansui SLE D2237 Owners Manual. Read or download the pdf for free.
If you want to contribute, please mail your pdfs to info@audioservicemanuals.com.
Page: 1 / 56
Extracted text from Sansui SLE D2237 Owners Manual (Ocr-read)
Page 1
EN2
ENGLISH
Location of the required marking
The rating sheet and the safety caution are
on the rear of the unit.
The lightning flash with arrowhead
symbol, within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product's enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user's authority to operate this equipment.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OPEN FLAMES AWAY
FROM THIS PRODUCT AT TIMES.
CAUTION: TO PREVENT ELECTRIC SHOCK. DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE
FULLY INSERTED TO PREVENT BLADE EXPOSURE.
Record the model number and serial number.
Model number Serial number
FCC Declaration of Conformity Compliance Statement
(Part 15):
The Sansui SLED2237, LED-LCD HDTV complies with Part
15 of the FCC rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
The party responsible for compliance to these rules is:
ORION AMERICA,INC.
1105 SOUTH MAIN STREET PRINCETON, INDIANA
47670,U.S.A
Ph: 1-800-289-0980
Page 2
3EN
15) Apparatus should not be exposed to dripping or splashing, and objects filled with liquids, such as
vases, should not be placed on the apparatus.
16) An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from touching such power lines or
circuits, as contact with them might be fatal.
17) Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
18) Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into
the unit.
19) If an outside antenna or cable system is connected to the unit, be sure the
antenna or cable system is grounded
to provide some protection against
voltage surges and built-up static
charges, Section 810 of the National
Electrical Code, ANSI/NFPA 70, provides
information with respect to proper
grounding of the mast and supporting
structure, grounding of the lead-in
wire to an antenna discharge unit, size
of grounding conductors, location of
antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810 20)ANTENNA LEAD IN WIRE
GROUNDING CONDUCTORS
(NEC SECTION 810 21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
GROUND
CLAMP
ELECTRIC SERVICE EQUIPMENT
NEC NATIONAL ELECTRICAL CODE
S2898A
EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
Page 24
25EN
Troubleshooting
SYMPTOMS POSSIBLE SOLUTIONS
Digital
broadcasting
screen
problem.Check digital signal strength. -
No CATV
reception.Check all Cable TV connections.
Set Signal Type menu option to the
Cable mode.
Station or Cable TV system problems,
try another station. -
-
-
Horizontal or
diagonal bars
on screen.Check antenna connections, adjust or
re-direct antenna.
Check for sources of possible
interference. -
-
No reception
above
channel 13.Make sure Signal Type option is in the
appropriate mode.
If using antenna, check UHF antenna
connections. -
-
No Remote
operation.Batteries are weak, dead or inserted
incorrectly.
Remote is out of range, move closer to
TV (within 15 feet).
Make sure Remote is aimed at sensor.
Confirm there are no obstructions
between the Remote and the TV.
Make sure the power cord is plugged in. -
-
-
-
-
TV shuts off.Sleep Timer is set.
Power interrupted. -
-
Closed
Caption is not
activated.TV station experiencing problems or
program tuned is not closed captioned.
Try another channel.
Check Cable TV connection or VHF/UHF
antenna, reposition or rotate antenna.
Set closed caption decoder in the menu. -
-
-
TV is not
shown in your
language.Select proper language in the menu
options. -
Cannot delete
E-POP.Set the E-POP Demo in the Auto Setup
menu to Off .
-
Use the following checklist for troubleshooting if you have problems with your TV. Consult your local dealer or
service outlet if problems persist. Be sure all connections are properly made when using with other units.
SYMPTOMS POSSIBLE SOLUTIONS
TV does not
operate.Make sure the power cord is plugged in.
Try another AC outlet.
Power is off, check fuse or circuit breaker.
Unplug unit for an hour, then plug it back
in. -
-
-
-
Poor sound
or no sound.Station or Cable TV experiencing
problems, tune to another station.
Check sound adjustments (VOL +/- or
MUTE).
Check for sources of possible
interference. -
-
-
Poor picture
or no picture.Station or Cable TV experiencing
problems, tune to another station.
Make sure channels are set into memory.
Check antenna or Cable TV
connections, adjust antenna.
Check for sources of possible
interference.
Check picture control adjustments. -
-
-
-
-
Poor
reception on
some
channels.Station or Cable TV experiencing
problems, tune to another station.
Make sure channels are set into memory.
Station is weak, adjust antenna to
receive desired station.
Check for sources of possible
interference. -
-
-
-
Poor color or
no color.Station or Cable TV experiencing
problems, tune to another station.
Make sure channels are set into memory.
Check picture control adjustments.
Check antenna or Cable TV
connections, adjust antenna.
Check for sources of possible
interference. -
-
-
-
-
Picture
wobbles or
drifts.Station or Cable TV experiencing
problems, tune to another station.
Make sure channels are set into memory.
Cable TV company is scrambling signal.
Adjust antenna. -
-
-
-
FOR CUSTOMER SERVICE, ADDITIONAL SET-UP AND OPERATING ASSISTANCE, OR TO ORDER ACCESSORIES PLEASE CALL:
18002890980
WHEN CALLING CUSTOMER SERVICE PLEASE HAVE YOUR MODEL NUMBER READY
OR WRITE TO:
ORION SALES, INC.
3471 N. UNION DR.
OLNEY, ILLINOIS 62450
FOR INFORMATION ON OUR OTHER PRODUCTS, TO ORDER ACCESSORIES ONLINE,
OR FOR RECYCLING INFORMATION, PLEASE VISIT OUR WEBSITE AT
www.sansuiproducts.com
BLOCK NOISE / PICTURE FREEZE
Block noise or picture freeze may appear on the screen caused by weak signals, interference from automobile
ignition systems, neon lamps or AC powered tools and appliances such as drills or hair dryers.