This is the 12 pages manual for Roberts 192 FT Service Manual. Read or download the pdf for free.
If you want to contribute, please mail your pdfs to info@audioservicemanuals.com.
Page: 1 / 12
Extracted text from Roberts 192 FT Service Manual (Ocr-read)
Page 1
FRtrOUENCY RESPONSE:
40
to 15,000 cps at ? l/2tps *2 db; 40 to 9,b00 cps at 3 3/4 ips + 3 db.
SIGNAL- TO. NOIS E RATIO:
55
db below recorded "0" Ievel.
WOW AND FLUTTER:
Les s than 0. 1B7o rms.
HEADS:
FuIl-track erase and record/playback in shielded housing.
SPECIFICATIONS
PREPA RING FOR
OPERATION
OUTPUT:
6 watts undistorted.
REEL
SIZE:
?" maximum (up to 2400 ft. of tape).
POWER
REQI]IREMENTS:
95 to 120 volts AC, 60 cvcles, 50 watts.
SIZE: 15
3/4" xt4 t/2" xI t/2".
WEIGHT:
Approx. 28 lbs.
l.
t
Remove lid from carrying
Remove microphone and
storage compartment on case.
case.
AC
supply cord from
left side of earrying
3. Make certain all controls are in ttre neutral po-
sition.
FUNCTION OF CONTROLS
0n-Off Switch
When the switch is pushed to the All-On posi-
tion, power isturned onto theamplilier and tapedeck. When the switch isin the Amp-Off position, power
is applied to the tape deck only. The Of{ position turns the power
off to the entire unit.
Volume
Turning this control elockwise increases the
volume during playback and the recording level when recording.
Tone
This control functions in playback only. Turn- ing theeontrol clockwise increases
thehigh frequency responae and turning the control counterclockwise attenuates
the high frequency response.
PIay-Record
and Record Lock
This is a 3-position eontrol: Stop, Piay, and Record. Turning this control elocknrise from the Stop
position, places the unit in play. Depressing the Record Lock and turning the
control to the Record
position at the same time, places the unit in Record"
N0TE: This control is interlocked with the Rewind-Forward control. It must be in the Stop position before
the
Rewind-For- ward control can be operated.
Rewind-Forward
Turning this control to the left places the unit in the Rewind model to the right places
the unit in
Forward mode of operation.
NOTE: This control is interlocked with the Play-Record control. It must
be in the
Stop position before the play-Record con- trol can be operated.
Pause
When
this lever is raised, pressure is removed from the eapstan, and the take-up reel is disengaged. This permits spot editing and momentary stops.
PAGE 2
Page 2
.:, {?'ttf i
()
Fig. l. TopVieur of Tape Transport Mechanism.
O PERATI NG I NSTRUCTIONS
3
Op
E9'tr
tp
sdtt{ Threading the Tape
1. Place a full reel of tape on the supply reel spin- dle (27),
making certain the reel slots engage
the protrusions on the pan. Place an empty reel on the
take-up spindle (67),
again makingcertain
the slots engage the protrusions on the pan.
2. Unwind about 14 inches of tape from the supply reel. HoId a section of tape taut and insert into
the tape slot, making sure the dtrll-coated side
faces the rear of the recorder.
3. Insert the free end of the tape into one of the slots in thehub of the take-up reel. While hold- ing the
end in place, rotate
the reel to secure the tape and take up any slack.
To Make a Recording
I. PIug a microphone into
the Microphone jack.
Place
the High Z iiltric- Low Z Mic switch in the proper position to match the impedance of the microphone.
2. Plaee the Pause lever in the
Up positionl de- press the Record Loek button and at the same time rotate the Play-Record control to the Record position.
3. Preset therecording
level by adjusting
the Vol- ume control until the indicator goes up to the
red portion of the scale but
does not enter the red portion except
on loud passages.
CAUTION: Do not eonnect a speaker or other low impedance load to the Output jack
while
making a recording.
To
Play Back a Tape
1. Thread the tape as
described under
"Threading
the Tape".
2. Turn the unit on and allow a few seconds for it to warm up.
3. Turn the
Play-Record control to play.
4. Adjust the volume and tone to the desired list- ening level.
Speed Change
To change the tape speed from 7 L/ Z to B B/ 4 ips, remove
the thumbscrew and bushing from the capstan. When the bushing is not being used, store it on the
bushing post.
lndex
Counter
Aftera tape is threadedon
the recorder, set the index counter to "000". The index numbers ean
then
atoF(fm7
J(lr
PAGE 3