This is the 66 pages manual for Nad T 512 C Service Manual. Read or download the pdf for free.
If you want to contribute, please mail your pdfs to info@audioservicemanuals.com.
Page: 1 / 66
Extracted text from Nad T 512 C Service Manual (Ocr-read)
1-4
SERVICING PRECAUTIONS
CAUTION : Before servicing the DVD covered by this service
data and its supplements and addends, read and follow the
SAFETY PRECAUTIONS. NOTE : if unforeseen circum-
stances create conflict between the following servicing pre-
cautions and any of the safety precautions in this publica-
tions, always follow the safety precautions.
Remembers Safety First:
General Servicing Precautions
1. Always unplug the DVD AC power cord from the AC
power source before:
(1) Removing or reinstalling any component, circuit board,
module, or any other assembly.
(2) Disconnection or reconnecting any internal electrical
plug or other electrical connection.
(3) Connecting a test substitute in parallel with an elec-
trolytic capacitor.
Caution : A wrong part substitution or incorrect
polarity installation of electrolytic capacitors may result
in an explosion hazard.
2. Do not spray chemicals on or near this DVD or any of
its assemblies.
3. Unless specified otherwise in this service data, clean
electrical contacts by applying an appropriate contact
cleaning solution to the contacts with a pipe cleaner,
cotton-tipped swab, or comparable soft applicator.
Unless specified otherwise in this service data, lubrication
of contacts is not required.
4. Do not defeat any plug/socket B+ voltage interlocks with
whitch instruments covered by this service manual might
be equipped.
5. Do not apply AC power to this DVD and/or any of its
electrical assemblies unless all solid-state device heat
sinks are cerrectly installed.
6. Always connect test instrument ground lead to the
appropriate ground before connection the test instrument
positive lead. Always remove the test instrument ground
lead last.
Insulation Checking Procedure
Disconnect the attachment plug from the AC outlet and turn
the power on. Connect an insulation resistance meter(500V)
to the blades of the attachment plug. The insulation resis-
tance between each blade of the attachment plug and acces-
sible conductive parts (Note 1) should be more than 1M-
ohm.
Note 1 : Accessible Conductive Parts including Metal pan-
els, Input terminals, Earphone jacks, etc.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged
easily by static electricity. Such components commonly are
called Electrostatically Sensitive (ES) Devices. Examples of
typical ES devices are integrated circuits and some field
effect transistors and semiconductor chip components.
The following techniques should be used to help reduce the
incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor compo-
nent or semiconductor-equipped assembly, drain off any
electrostatic charge on your body by touching a known
earth ground. Alternatively, obtain and wear a commer-
cially available discharging wrist strap device, which
should be removed for potential shock reasons prior to
applying power to the unit under test.
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such
as aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
3. Use only a grouned-tip soldering iron to solder or unsolder
ES devices.
4. Use only an anti-static solder removal device. Some
solder removal devices not classified a anti-static can
generate electrical charges sufficient to damage ES
devices.
5. Do not use freon-propelled chemicals. These can
generate electrical charge sufficient to damage ES
devices.
6. Do not remove a replacement ES device from its protec
tive package until immediately before you are ready to
install it. (Most replacement ES devices are packaged with
leads electrically shorted together by conductive foam,
aluminum foil, or comparable conductive material).
7. Immediately before removing the protective material from
the leads of a replacement ES device, touch the protective
material to the chassis or circuit assembly into which the
device will be installed.
Caution : Be sure no power is applied to the chassis or
circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Normally harmless motion such
as the brushing together of your clothes fabric or the lifting
of your foot from a carpeted floor can generate static elec-
tricity sufficient to damage an ES device.)
3-8
Does signal pulse
input to IC201 Pins 53, 54 when
the power is on?
Does signal goes
"High" to IC201 Pin186 when the
power is on?
Does
TTL pulse output to
IC201 Pin 156? Does
33.8688MHz clock input
to IC201 Pin 59?
Is IC201
Pins 79, 80, 84, 88 voltage
about 2.2V?
Replace IC201
(IC206 soldering or IC defect).
Check power circuit.
Check "2.µ-COM Part".
Replace X201 or IC206
(33MHz clock defect)
CHECK POINT(General)
5. RF/Servo Circuit
A.
END
NO
NO
NO NO
NO YES
YES
YES YES
YES
Page 57
5-14
S AL LOCA.NO PART NO(LG)ABCDDESCRIPTION SPECIFICATION REMARKS
R960 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R961 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R969 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R970 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R971 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R972 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R973 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R974 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R975 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R976 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R977 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R978 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R979 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R980 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
R981 0RD1003F608OOOORESISTOR,FIXED CARBON FILM 100K OHM 1/6 W 5.00% TA26
RC901 6712R1938GAOOOOREMOTE CONTROLLER RECEIVER TSOP2838WE1 VISHAY(TEMIC) 37-
REMOCON RECEIVER
RC901 6712R1938GAOOOOREMOTE CONTROLLER RECEIVER TSOP2838WE1 VISHAY(TEMIC) 37-
SENSOR
IC102 657-063AOOOOSENSOR LTV-817B,PHOTO COUPLER(LITEON)
SWITCH
SW601 6600R-SH02A O O SWITCH,SLIDE SKQ-23D15-G5-NA LUPFUNG DC 30
SW602 6600R-SH18AOOOOSWITCH,TACT CSS-4206 CHANG SHIN NON DC 30V
SW902 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW903 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW904 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW905 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW906 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW907 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW908 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW910 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW911 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW912 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW913 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW914 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW915 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW916 556-219BOOOOSWITCH,TACT THVV502GAA POSTECH DC 12 V 5-
SW919 6600RRT001TOOOOSWITCH,TACT THVH471BAA POSTECH 12V DC 50MA
VARIABLE RESISTOR
CRYSTAL
X201 6202R-BM04COOOORESONATOR,CRYSTAL HC-49/S BUBANG 33-8688MHZ 5
X501 6202R-BL06COOOORESONATOR,CRYSTAL HC-49/S BUBANG 27MHZ 20PPM 1
X901 6212BA3004COOOORESONATOR,CERAMIC CRTL6.00MS0T CORETECH 6MHZ +/-
ZENER DIODE
ZD101 0DZ562609AAOOOODIODE,ZENER GDZJ5.6B 26MM TP GRANDE DO34
ZD605 0DZ332609FBOOOODIODE,ZENERS GDZJ3.3B 26MM GRANDE TP26 DO34
ZD606 0DZ332609FBOOOODIODE,ZENERS GDZJ3.3B 26MM GRANDE TP26 DO34
ZD611 0DZ332609FB O O DIODE,ZENERS GDZJ3.3B 26MM GRANDE TP26 DO34
ZD635 0DZ332609FBOOOODIODE,ZENERS GDZJ3.3B 26MM GRANDE TP26 DO34
ZD637 0DZ332609FBOOOODIODE,ZENERS GDZJ3.3B 26MM GRANDE TP26 DO34
ZD639 0DZ562609AA O O DIODE,ZENER GDZJ5.6B 26MM TP GRANDE DO34
ZD640 0DZ562609AA O O DIODE,ZENER GDZJ5.6B 26MM TP GRANDE DO34
ZD641 0DZ332609FB O O DIODE,ZENERS GDZJ3.3B 26MM GRANDE TP26 DO34
ZD643 0DZ332609FB O O DIODE,ZENERS GDZJ3.3B 26MM GRANDE TP26 DO34
CIRCUIT BOARD ASSY & CONNECTOR
P4301 6630R-BE024OOOOCONNECTOR (CIRC),BOARD TO BOAR 2254-30P-T/JE611-A2T-30T POWER
P5402 6630R-BE034OOOOCONNECTOR (CIRC),BOARD TO BOAR 2254-30S-T/JE611-B2G-30R POWER
P5901 6630R-BE034OOOOCONNECTOR (CIRC),BOARD TO BOAR 2254-30S-T/JE611-B2G-30R POWER