Kenwood DVFR 5070 S Service Manual

Page 1

DV7705(K)int1 03.7.810:16 «>9 1 A I
x

3Vf§3D-��73VE1Efi5O7o-s KENWOOD

SERVICE MANUAL

© 2003-6 PRINTED IN KOREA
B51-5860-00 (K/K) 1356

Cabinet panel * Crystal Window * Button assy
(A60-) (303-) (K29-8327-08)

KENWOOD :7]: 7 ; , 7N7}
man I l
I:fi :E:
I mm IEI
. l
l l L , , , , , l
Knob Button
(K27-2508-08) (K29-8328-05)
/ \ /A
K / K
Top cover * Phono socket Optical out AC power cord bushing
(A01 -) (E63-1227-08) (GP1F32T) (J42-0350-08)
\ (1

ileED mm
owr Wm

W @©

llllllllllllllllllll ( N
llllllll llllllllll mg)

9

Scan dual * DIN socket Phono socket AC power cord *
(E40-) (E68-0018-08) (E63-1244-os) (530-)

* Refer to parts list on page 15.

In compliance WIIh Federal Regulations, fOIIDWIUQ are repro- KENWOOD Corpt certifies this equipment conforms to DHHS
duction of labels on, or inside the product relating to laser Regulations No.21 CFR 1040_ 10, Chapter 1_ subchapterJ.
product safety.
DANGER : Laser radiation when open and interlock defeated.
. . . . . AVOID DIFIECT EXPOSURE TO BEAM. .
Caution : No connection of ground line If disassemble 70%
the unit. Please connect the ground line on If
rear panel, PCBs, Chassis and some others.

Page 2

J Dwosmfimp 03.7.810:16 «us/*2 C
DV-705/DVF-R5070-S

ACCESSORIES / CAUTIONS

Accessories
Audio video cord (Red, White, Yellow) ...(1) Remote control unit ...(1) Batteries(Ft6/AA) ...(2) Coaxial cable ...(1)

(E30-2990-08) (A70-1570-08) (E30-7235-08)

Cautions

Operation to reset
The microprocessor may fall into malfunction (impos-

0 During stop mode, press the MENU key on the remote to
enter "Control Panel" menu.

sibility to operate erroneous display, etc.) when the 9 Select the "System" icon, then press the Cursor right (>) key.
power cord is unplugged while power is ON or due to 9 Select "Restore Setup Info".

an external factor. 0 Press the numeric keys as shown below.

In this case, switch off the power, wait for several sec- Press .v E] I then press the ENTER keli-
onds, and then switch the power on again_ When resetting is done according to this method, all settings,

Return to the factory defaults by resetting the micropro- including the settings IOT password and parental level, Will be

cessor is done as shown as follows.

reset to the factory deiaults.

Note related to transportation and movement

Before transporting or moving this unit, carry out the

Caution on condensation

Condensation (oi dew) may occur inside the unit when there is agreat

following operations. difference in temperature between this unit andtt-Ie outside. Thisunit

1_ Set the POWER ON/OFF switch to the ON may not iunction properly if condensation occurs. In this case, leave
without loading a disc. the unit for afew hours and restart the operation after the condensa-
2. Wait a few secondsand verify that the display tion hanried P-

/ \
shown appears. Be speciallycautious againstcondensation in the following circum-

stances:
When this unit is carried from one place to another across a large

difference in temperature, when the humidity inthe room where

3. Set the POWER ON/OFF switch to OFF_ this unit is installed increases, etc.

The marking of products using lasers
(For countries other fhan U.S.A. and Iii-Military)

VISIBLEAND INVISIBLE LASER RADIATION
CLASS 1 WHEN OPEN. Do NOT STARE INTO THE BEAM on
LASER PRODUCT VIEW DIRECTLYWITH OPTICALINSTRUMENTS.
DO NOT PRESSON THIS SURFACE

The marking this product has been classilied as Class 1. It Inside this laser product. a laser diode classified as ClassZ laser radia-
means that there Is no danger of hazardous radiation outside tion is contained as alerted by the intemal caution label shown above. Do
the product. not stare into beam or View directly with optical instruments.

Location: Back panel Location: DVD laser pick-up unit cover inside this product

Manufactured under license from Dolby Laboratories.

"Dolby" and the double-D symbol are trademarks of Dolby
Laboratories.

"DTS" and "DTS Digital Out" are trade-
marks of Digital Theater Systems, Inc. dis

CAUTION:

Use of controls or adjustments or pertormance 01 procedures other than
those specified herein may result In hazardous radiation exposure.

In compliancewlth Federal Regulations,the tollowlng are reproducttons
ot labels on, or Inside the product relating to laser product satety.

I KENWOOD CORPORATION I
I 2967-3, ISHIKAWA-CHO, I
I HACHIOJl-SHI, I
TOKVO, JAPAN

KENWOOD CORP. CERTIFIESTHIS EQUIPMENT

CONFORMS TO DHHS REGULATIONS NO. 21 CFR
1040.10, CHAPTER1, SUBCHAPTERJ.

CAUTION- LASERRADIATION WHEN OPEN.
DO NOT STARE INTO BEAM.

Location: Laser Pick-up Unlt Cover Inside this product

I;