Kenwood DPJ 2070 Owners Manual

Page 1

CI..W\NEI>I

CD PLAYER

DP-J207O

INSTRUCTION MANUAL

KENWOOD CORPORATION

This unit is designed for home use only.

lithe unit is used in a location other than at home, such as in a shop (for commercial
use), in e car or in a ship, etc, and is damaged, a service fee may be charged even
during the warranty period.

Far yourrecards

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card,
and in the space provided below. Refer to the model and serial numbers whenever you call upon your
dealer for information or service on this product.

Model H Serial Number

Unpacking

Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost.
Examine the unit for any possibility of shipping damage. If your unit is damaged or falls to operate, notify
your dealer immediately. if your unit was shipped to you directly, notify the shipping company without
delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier
for shipping damage.

We recommend that you retain the original carton and packing materials for use should you transport
or ship the unit In the future.

Accessories

Liner note file (1) Audio cord 1|) System control cord (1)

Batteries (RS/AA) (2) A1: plug adapter 11)

:1 e6

ass Use to adapt the plug on the power cord to the shape oi the wall outlet,
(Accessory only for regions where use is necessary.)

For Europe and WC
C 6 NOTICE

This lthesei equipment(s) is (are) In conformity with the provision of EMC Directive, sense/EEC,
92/31/EEC and WISE/EEC.

DOM PACT

DIGITAL AUDIO

ace-1 995-10 ® (K.P,M.X,V,T) El
96/12111096785432195/1211109376

Page 2

I . . T , - , . , -
' ' E I l I l I yr autm Bills [alecareu IDEHSIII'ESBEU .

DPuanm [En]
Units are designed for operation as follows.

0.5.14. and L'anad
Australia

MAC 230 Vunly
.AL1m-120/220-240 szilchable

For the United Kingdom *AL voltage selection

Factory lifted mou|ded mains plug The AC voltage selector switch on'the rear panel is set to the
voltage that prevails In the area to thoh the unit is shipped, Before
conneotIng the power cord to your AC outlet, make sure that the

1.The mains plug contains a fUSE- FBI lePIacememi use only 3 13- setting posmon of this switch matches your line voltage, If not, it
Amp ASTA-approved (881362] fuse. must be set to your voltage in accordance with the following
direction
2. The fuse cover must be refitted when replacing the fuse in the

moulded plug, AC voltage selector switch

3 Do not cutoff the mains plug from this equipment, if the plug fitted
is not suitable for the power points in your home or the cable is too ffwm
short to reach a power point, men obtain an appropriate safety
approved extension lead or adapter, or consult your dealer.

IF nonemeless the mains plug is out off, remove the fuse and
dispose of the plug immediately, to avoid a possible shock hazard
by inadvertent connection to the mains supply.

Move switch lover to match your
llna voltage with a small smw-
driver or other pointed tool.

IMPORTANT: The wires in the mains lead are coloured in accordance
with the following code:
Blue : Neutral
Brown : Live
Do not connect those leads to the earth terminal of a three Our warranty does not cover damage caused by excessive line
voltage due to improper setting of the AC voltage selector switch.

Safety precautions . 7
WARNING: TO PREVENT FIRE 0R ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACKI.NOUSER-SERVICEABLE PARTSINSIDE,REFERSERVICINGTOQUALIFIED SERVICE

RISK or ELECTRIC SHD
DOHOY OPEN PERSONNEL.

THE PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE PRODUCTS ENCLOSURE THAT MAY BE OF SUFFICIENT

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EOUILATERALTRIANGLE, IS INTENDED TO ALERT THE USER TO
A MAGNITUDE T0 CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EOUILATERAL TRIANGLE iS INTENDED TO ALERT THE USER TO THE PRESENCE OF
IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS INTHE LITERATURE ACCOMPANYING THE APPLIANCE.

The marking of products using lasers
(Except for some areas.)

CLASS 1
LASER PRODUCT
The label is attached to the rear panel and says that the component
uses laser beams that have been classified as Class 1 . It means that

the unit Is utilizing laser beams that are at a weaker class. There is
no danger of hazardous radiation outside the unit.