This is the 27 pages manual for Heathkit IM 17 Manual.
Read or download the pdf for free.
If you want to contribute, please mail your pdfs to info@audioservicemanuals.com.
77,?73W7 fl
PRICE $2.00
HE'ATI-IKITQ
_I-IE.A.THKIT ,
UTILITY SOLID-STATE VOLTMETER
MODEL IM-17
595-921-03
This chart is a guide to commonly used types of elec-
tronic components. The symbols and related illustra-
TYPICAL COMPONENT TYPES
tions should prove helpful in identlf
reading the schematic diagrams.
ying most parts and
RESISTOR
GRID TUBE
CATHODE
/ FILAMENT
POTENTIOMETER v.
ELECTROLYTIC PN p coLLEcroR
(CONTROL) CAPACITOR TRANSISTOR
BASE
EMITTER
COLLECTofi
NPN EMITTER
RECTIFIER
I (DIODE)
TRANSFORMER
| | (ADJUSTABLE
' POWDERED IRON
l I CORE)ARROW
I I INDICATES DIR-
| I
ECTIoN 0F CORE
MOVEMENT To ~
TRANSFORMER 7
I
(ADJUSTABLE
CORE)
ILLUMINATING -
BULB &
PHONE
O JACK
___[l
~__./r
SPST SWITCH
8 METER m
. a
INDUCTOR
(COIL) fl SOGGLE)
l
_. 0'".-
DPDT
PIEZOELECTRIC ' SWITCH
[I CRYSTAL SPEAKER (ROTARY)
I O
D
O
O O
I
BINDING 0
POST [ MICR PHONE FUSE
i,
CONDUCTORS
, III'77 EARTH GROUND
ANTENNA ['3 - ::::::
_J_
GENERAL _ Loop ? CHASSIS GROUND
NOT
CONNECTED CONNECTE
DSHIELDED
Assembly
and
Operation
of the
HEATI-IKI-re
UTILITY SOLI D-STATE
VOLTMETER
Model IM-17
HEATH COMPANY
BENTON HARBOR, MICHIGAN 49022
I
TABLE OF CONTE NTS
Introduction...............
Parts List................
Step-By-Step Assembly
Rotary Switch Prewiring. .
Circuit Board Assembly. . . .
Panel Parts Mounting. . . . .
Panel Wiring. . .......--
Circuit Board Wiring. . . . . .
Final Wiring. . .
Calibration.............
Final Assembly. . . .........
Operation...l..............
Maintenance...............
Accessory Probes...........
In Case Of Difficulty. . . . . . . . .
Factory Repair Service. . . . . .
Troubleshooting Chart. . . . . . . .
SpecificatiODS. . . . . . . . . . . . . .
Circuit Description. . . . . . . . . .
Functional Parts List. . . . . . . .
Photograph. . . . ...........
Circuit Board X-Ray View. . . . .
Voltage Chart..............
Replacement Parts Price List. . .
Schematic (fold-out from Page). .
Applications (fold-out from Page).
...-o
24
25
26
2'7
28
29
30
30
31
31
32
\E/
itrol
'01 B
r the
The
' two
vire:
lugs
fore
is of
8 of
'7 of
cted
yair.
50f
40f
cted
air.
lide
lide
:ted
air.
m-
-I-IEATHKIT=
) Prepare the following lengths of hookup wire:
1" red
1" black
3-1/2" red
3-1/2" black
3-1/2" black
4- 3/4" White
(V/(Connect a 1" red wire between lugs 315-1)
and 4 (NS) of slide switch D.
(WConnect a 1" black wire between lugs 1 (NS)
and 6 (S-1) of slide switch D.
, Connect a 3-1/2" red wire to lug 4 of slide
switch D (8-2).
(, Connect a 3-1/2" black wireto lugl of slide
switch D (8-2).
(\1) Twist together the red from lug 4 andblack
wire from lug 1 of slide switch D.
Wehneot a 3-1/2" black wire to lug 50f slide
switch D (S-l).
("flfléfigect a 4-3/4" white wire to lugZ of slide
switch D (S-l).
(ii. wist together the black wire from lug 5 and
white wire from lug 2 of slide switch D.
CIRCUIT BOARD WIRING
Refer to Pictorial 8 (fold-out from this Page)
for the following steps.
(\é Prepare the following lengths of hookup wire:
1" white
1-1/4" white
3" red
3" black
( Mnnecta'l" length of white wire from lug 5
of the Bias Adj control (8-1) to circuit
board hole M (8-1).
( Connect a 1-1/4" length of white wire from
lug 1 of the Bias Adj control (S-1)to circuit
board hole L (8-1).
(V/Connwt one end ofa 3" red wire to hole F in
the circuit board (8-1).
Page 13
MConnect one end of a 3"b1ack wire to hole E
in the circuit board (S-l).
(I)/Twist these two wires together to form a
twisted pair. Position them as shown.
( W Connect the free end of the blacktest lead to
circuit board hole K (S-l).
Connect the twisted wires from control B as
follov/s:
Red wire to lug 2 on the Bias Adj control
(S-l).
(\KWhite wire to lug 6 on the Bias Adj con-
trol (S-l).
(«Black wire to circuit board hole N (S-l).
Connect the wires from switch E to the circuit
boyd as follows:
( ,) Either white wire to hole P (8-1), and the
other white wire to hole R (S-l).
Wither black wire to hole T (8-1), and the
tier black wire to hole s (3-1).
Either red wire to hole W (S-1), and the
other red wire to hole U (S-l).
(\/Connect the loose end of the red test lead
to lug B9 of the rotary switch (S-l).
Connect the red and black twisted pair from
slidf switch D as follows:
(
Red wire to circuit board hole J (S-l).
(«Black wire to circuit board hole H (S-l).
Co ect the black and white twisted pair from
sli 6 switch D to the rotary switch as follows:
(J) White wire to lug A10 (S-l).
( Dlack wire to lug A4 (S-l).
) Connect the inner lead of the 5-1/2" shielded
cable from phone jack F to lug C4 of the ro-
tary switch (8-1), and the shield to circuit
board hole G'(S-1).
355°??? INSET
2:33;:
SIDE VIEW
PICTORIAL 8