Kenwood KCAS 200 Owners Manual

Page 1

CD / MD CHANGER SWITCHING UNIT

KCA-SZOO

INSTRUCTION MANUAL

KENWOOD

KENWOOD CORPORATION

©PRINTED IN JAPAN 864-0591-00 (W,E.J)(MC)
96/8765432195/121110987

The CD/IVID changer swrtchrng unit can be used to control up to two dlSC changers when It IS connected to
the center unlt that has the dISC changer control tunctron

ILampanents i Switching unit .......................
2 Controller (cord lengt m1
3, Connection cable (2 m) ........

Installation

.1 4 Magic tape ....................................
.1 5 Self-tapping screwlo 4X 16 mm)
.1 get Cable band .............................

7, Double-sided adhesive tape.

La-nN'N

llnstalling the switching unit with a
board in the trunk space

llnstalling the switching unit on the carpet
under a seat

5 Self tapptng screwtm 4 x 16 mm)

6 Cable band

I Swttchtng untt

carpet

Board etc

meme WW" 0 more 1 Remove the backtng from the magic tape 123:? and attach It to the

bottom of the swttchtng untt 71:, Install the switching untt on the
carpet,
2 Btnd the cables wrth cable band is;

1 Install the swttchtng untt wrth selfetappmg
screws T5" (11) 4 >< 16 mm)
2 Btnd the cables wtth cable band 6

0 Install the swttchtng untt it In places that do not obstruct dnvrng

0 Install the swttchtng untt '1, tn places where It IE not touched by the tip 01 the shoes of a rear seat passenger

- Do not Install the unit In places where It IS exposed to dtrect sunltght. hrgh heat, or where water may splash over It
- Do not place anythtng on top of the swrtchtng untt It?

Ilnstalling the controller

g { 2 Controller

1 the off the Installatton locatton With a cleanrng cloth
Remove the
I backing ACAUTION

- Install the controller :27 on a flat surface, It It IS Installed on a curved
7 surface, the tape adheston may weaken and the controller may come off.
'7 DOUbIe'Sde" . Do not Install the controller 2) In places (such as on the dashboard) where
\adheswetape II IS exposed to dtrect sunltght and the temperature becomes htgh.
\ Otherwrse, the controller :2» erI become deformed and unusable.
. Install the controller f2; tn places that do not obstruct drlvrng Install the
controller EU temporartly and verify that the handle, shttt knob, and side
brake can be operated smoothly

2 Secure the controller 12: In the specrhed place wrth the doublesrded
adhesrve tape 7»

Page 2

Connection

Changer control output
It the cutout connector is a rectangular connector

the CAVSDZOO conversion cable is required T0
T0 CHANGER 1

TO
CHANGER 2

2 Controller p

t

i ! CAUTION

1 It you connect a model IKRCVBOl/9OW/88l/99t, KDC-8003/7003/7OOA,
1 etc) which can swrtch between drsc changers l and 2 by the center
urtt, the controller 2 mL.St not be connected If rt rs connected, the

' dlSC auto changers may not work proaerlv

=
l Swrtchrng unit

0
1 CONTROLLER

CD changer extenSron cable tsupphed With the CD auto changer)

lithe dlSC changer has a select sw to" or 1D]
| x .
rt, eaye it in te original posrtron tr

CD changer (KDC-C603/CSO3, etc.)

MD Changer (KMD»C80)

- The figure shows that one CD auto changer and one Ile auto changer are connected Two CD auto changers or two
lle auto changers may be connected
- It you wrsh to adjust the cable length to accordance With the installation location of the swrtchrng unit, such as In the

trunk space, the CD changer extension cable may be used instead of the COflfleCIlOfl cable 3

Switching between disc auto changers

Ilf you can switch disc auto changers 1 and 2 by the center unit:
(KRC-801/901/881/991, KDC-8003/7003/7004, etc.)

MD changer extensron cable lsupplred With the MD auto changer)

- Each time the SRC button on the center unrt rs
pressed, the drsc auto changer mode changes '1.'-] 1 > Noifld'calor
between dlSC changer modes I and 2 When the ' I.' [do
desired drsc changer number )5 selected, playing - - \
Starts N02 indicator

IOther center units
- Select the dlSC changer to be controlled With the
controller 2 When the dlSC changer mode is selected
wrth the SRC button (or CD button), playing begins

- You cannot change the discrchanger number while a drsc changer is playing To change the dtscrchanger number, press
the SRC button (or CD button) to stop playing, then change the dtscvchanger number With the controller 2 Select the
dlSC changer mode With the SFIC button (or CD button)

- When the discachanger number Is changed and play begins, the drsc~changer number data before It was swrtched may
be shown temporarily on the dlSDIBV of the center unit

IMPORTANT INFORMATION

This unit is NOT designed to be connected directly to a CD changer that was manufactured and sold before 1994.

If you plan to use such units, please read the following information carefully.

- To control KDC-CZOO / KDC~6300 / KDC-C40CI
A CAaDS)OO (sold separately as an OpilOfla) accessory), along With the control box and extenston cord supplied wtth
the CD changer, are required

- To control KDC-CSOI IKIJC-CBUD/KDC-CBOO/KDC-CBOI / KDC-cw1
A CAVDS)OO (sold separately as an optional accessory), along With the extension cord supplied With the CD changer,
are required

' KDC-C1IIO/KDC»C3OZ/CZO5 / C705 and CD changer Manufactured by Other Companies are not compatible with this Kenwnod
model.

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO THIS UNIT AND/DR THE CD CHANGER

Disc changer 2

You can swrtch between
dISC changers I and 2 by
the swrtchlng unrt